6 Best Easy Ways How To Fix HP Printer Error 59.F0

There could be a problem with the printer that prevents it from working. If the printer is restarted, the error issue will typically be fixed. However, if the paper path is the source of the problem, then a different solution is required. A botched transfer can result in the HP printer error 59.F0.

Due to transfer alienation or the SR9 sensor factor, the Intermediate Transfer Belt (ITB) scenario becomes stopped and does not rotate fully. K Sensor, or known to be the transfer roller release sensor heavily relies on the SR9 sensor. The toner and fuser components can be reset to clear the 59.F0 fault. In this article, I’ll attempt to describe How to Fix HP Printer Error 59.F0.

The transfer may fail due to the following mistakes. The Intermediate Transfer Belt (ITB) can become trapped and stop rotating in a circumstance known as transfer alienation.

How to Fix HP Printer Error 59.F0

The failure in transfer alienation may be the root cause of the HP printer error 59.F0. When the Intermediate Transfer Belt (ITB) becomes stuck and does not spin completely, this is known as transfer alienation. An issue with the SR9 sensor is yet another potential cause of the HP printer error 59.F0.

The transfer-roller-disengagement sensor, commonly known as Sensor K, relies heavily on the SR9 sensor. The toner and fuser components can be reset to clear the 59.F0 Error. You could also attempt to revive your HP device. Additionally, you can examine the internal motor and the fuser motor for any problems.

All potential causes and solutions for HP printer error 59.F0 are mentioned below. We invite you to continue reading with us.

How Do I Fix Error 59 F0 On My HP Printer

Your HP printer’s ITB becoming stuck and unable to spin freely is one potential cause of an error at 59.F0. The SR9 sensor also occasionally has certain issues. The printer machine greatly depends on these two parts. It’s possible that a bad reroute means ITB can’t rotate completely. This is as a result of a potential SR9 sensor issue.

The printer engine’s internal motor could be another contributing factor. The fuser assembly must be rearranged, and the toner must be reset, in order to resolve Error Code 59.F0 on your HP printer. Then attempt to correctly configure ITB. This will allow you to examine the sensor’s functionality. These straightforward procedures can assist you in fixing printer-related issues

The steps How To Fix HP Printer Error 59.F0 are as follows;

Step 1: Resetting the Fuser assembly

Resetting the Fuser assembly is one way to address current issues. You must turn off the HP printer before you may reset the assembly. Before turning on the printer, attach the surge protector, but don’t forget to unplug it first.

Next, leave your HP device off for a while. The printer engine’s surge connector should be removed. After some time, turn on the printer. Reinstall the fuser unit to reset it after the HP printer has been revived. the primary transfer release must be accurate, thus do a sensor test in sensor monitor mode. Do the alienation drive after that.

Step 2: Reset The ITB

The next thing to perform is a test print if you have completed all the stages.

In order to fix the HP M477 59.F0 printer issue, ITB needs to be reset. You must examine each connection on the internal ITB. Additionally, you must ensure that the PCA and ITB that control the DC are connected properly. Reset ITB once all connections are secure.

To reset ITB, you can follow how to fix HP 59.f0 error below:

  • The printer’s right door should be opened.
  • Pull transfer belt assembly toward you while still holding the blue lever at a downward angle.
  • Pull the belt further till you can release a pair of two sizable handles.
  • Pull the transfer belt until it releases by holding the large lever on the transfer belt assembly.
  • Reverse the process for installing the new transfer belt.
  • During installation, you are not permitted to contact the transfer belt’s surface.
  • Open the “Control Panel” and then hit the “Home” button to reset the “New Transfer Kit Settings.”
  • Please choose “Manage Inventory” from the “Administration” menu after opening it.
  • Then choose “New Transfer Kit” after choosing “Inventory Rest.”
  • And choose “Yes,” then choose “Ok.”

You can calibrate the printer completely after successfully changing the transfer belt. This will aid in properly adjusting the color field and color tone.

Step 3: Test The ITB and The Flag

To resolve the HP printer problem 59.F0, manually test the ITB and the flag by turning the ITB gear. While spinning the white ITB gear, look for any variations. Check the SR9 sensor to see if the gear and flag are both working properly. The sensor is located in the control panel’s ITB cavity. To proceed, press the Home button and scroll down to highlight the Diagnostics menu.

All of the directions for this method are listed below:

  • First, rotate the “ITB” gear.
  • Then, please check for any fluctuation in the flag while you are rotating the white gear.
  • After that, if there is any damage to the flag, you may replace the “ITB”.
  • Then, in case the “ITB” is not damaged, please check the “Sensor SR9”.
  • Next, the “Sensor SR9” will be located inside the “ITB Cavity” in the “Control Panel”. You can Press the “Home” button and move down to highlight the “Diagnostics” menu using the arrow keys.
  • Then, for the next step, you can click on the “Ok” button.
  • And last, please choose the “Manual Sensor Test” option and then click on “Ok”.

Release the SR9 flag from within the ITB cavity. When you press the flag, the sensor reaction will be displayed on the display. The sensor would alternate between 0 and 1. If this does not occur, the sensor may need to be replaced.

Step 4: Reset Your HP Printer

If the HP printer issue 59.F0 persists, you can try resetting your device’s settings to default. Restoring them to their original state will make your device as good as new. Then, print a test page to ensure that the problem has been resolved.

Step 5: Replace the PCA Assembly

Here are the steps:

  • First, to Reset the printer, you can turn off the power by using power switch and wait for some time.
  • Remove the surge protector (if the user is using).
  • If the situation persists, the PCA Assembly should be replaced.
  • If the problem persists after changing the PCA assembly, you may need to replace the product.

Step 6: Verify The ITB

Here are the steps:

  • First, verify whether the ITB was installed adequately or not.
  • Then, you can reconnect the primary transfer disengagement sensor.
  • Next, please run the sensor test in the sensor monitor mode to verify that the primary transfer disengagement is functioning correctly; if not, you must replace it.
  • Then, perform the alienation drive.
  • And last, examine the fuser motor; if it is not working properly, you must replace it.

How To Perform ITB Alienation Test:

  • Remove the transfer belt assembly first.
  • Then, please remove the cyan cartridge by opening the toner access door.
  • After that, insert a flat-bladed screwdriver into the slot and leave it there until the test is completed. The inserted screwdriver then triggers toner access.
  • After that, pull it out, assemble it, and turn it on.
  • Finally, during the test, the gear must spin; if it does not spin or misses the spin, the fuser assembly is destroyed. And last, the only option is to repair or you can replace it.

You should have learned about the many causes of the HP printer error 59.F0 after reading this article about “How To Fix HP Printer Error 59.F0” thoroughly. I hope it helps you a lot. If not, you can find support and customer service options to help with your HP Printer problem’s in Official HP Support Website.

Read Also: How to Fix HP Printer Error Code 0xc19a0013

Images Source: HP.com